We install, repair and test primary and battery-backup pumps, and we start by asking whether your property needs one at all. If the water has a natural way to leave, we say so and save you the cost.
Why homeowners call us about sump pumps
- Standing water or soggy soil in the crawlspace after heavy rain
- A pump that runs constantly, or never turns on when the basin fills
- A float switch stuck against the basin wall
- Grinding, rattling or a loud hum from the pump motor
- Musty smells, efflorescence on stem walls or rising humidity under the house
- A pump that's 7–10 years old and has never been tested
- No backup during an atmospheric river, when power outages are most likely
What's included
Every sump pump installation & repair job in El Dorado Hills covers the essentials below — no vague scopes, no surprise add-ons:
- A drainage assessment of grading, gutters, existing drains and the crawlspace
- Basin installation or inspection at the lowest point of the space
- Primary pump supply and installation, with a check valve and secured float
- Discharge piping routed away from the foundation and off the sanitary sewer
- Battery backup installation and a charge-and-function test
- A full-cycle test, filling the basin until the pump starts and clears it
- Guidance on a seasonal test schedule and when to replace the pump
How we handle a sump pump job
- 1
Find where the water comes from
We trace whether it's a high water table, runoff against the foundation, a roof or gutter discharge, or a leaking pipe that only looks like groundwater.
- 2
Set the basin
The basin goes at the lowest point, with a firm base, a solid lid and room for the float to move freely.
- 3
Select and set the pump
Horsepower and lift height come from the discharge distance and volume, with a check valve to stop pumped water from draining back.
- 4
Route the discharge
Water is piped well away from the foundation and neighboring properties. It never goes to the sanitary sewer.
- 5
Test and add backup
We fill the basin to confirm the pump cycles and discharges, then install a battery backup that runs when the power is out.
Do foothill homes need a sump pump?
It depends on the lot. Many El Dorado Hills homes are built on engineered slabs with perimeter drainage and need nothing more. Hillside lots, crawlspace homes and houses with lower-level rooms cut into a slope can collect water that has nowhere to go, especially after the wet weeks that follow a Sierra storm.
We look at grading, existing drains and signs of past moisture before recommending a pump. Sometimes the fix is a downspout extension or regrading, not a pump. Honest scoping avoids the most common mistake, which is installing equipment to solve a drainage problem it can't reach.
Why a battery backup matters
Storms that raise the water table are the same storms that knock out power. A pump on household current stops exactly when you need it. A battery backup unit sits beside the primary, senses a rising float or a failed primary, and keeps pumping on stored power for hours.
- Test the pump before the wet season starts, not during it
- Replace backup batteries on the manufacturer's schedule
- Keep the basin free of silt, gravel and debris that jams the float
What a failed sump pump looks like in a crawlspace
Under a foothill home the signs are quieter than a flooded basement. You might notice damp soil, a musty smell inside the house, insulation sagging between the joists or mineral staining on the stem walls. By the time water is visible, it has often been present for a while.
We check the basin, the pump, the float and the discharge, and look for the reason water is collecting. A pump is only the answer when water has nowhere else to go. Otherwise we fix the grading, downspouts or a leaking pipe that was feeding the problem.
Before the storm season
The best time to service a pump is October, before the first atmospheric river, not the night of one. We clean the basin, test the float and check valve, confirm the discharge flows freely and put a load on the backup battery.
- Pour water in the basin and confirm the pump cycles and shuts off
- Clear the discharge line outlet of leaves, soil and ice
- Check that the pump's outlet is on a GFCI-protected circuit
- Replace aging backup batteries before the wet season
What affects the price
We use upfront, flat-rate pricing and give you the number before we start — no fake fixed quotes online, because the honest answer depends on your home. For sump pump installation & repair in El Dorado Hills, the main factors are:
- Whether you need a new basin or only a replacement pump
- Pump capacity, lift height and discharge distance
- Crawlspace access, which affects labor and equipment placement
- Battery backup or water-powered backup add-ons
- Trenching or piping needed to carry water away from the foundation
- Electrical work for a dedicated GFCI outlet and any permit requirements
Where we provide sump pump installation & repair
We service sump pumps in El Dorado Hills and neighboring Cameron Park, Shingle Springs, Placerville and Folsom. Crawlspace homes on sloped lots, lower-level rooms cut into a hillside and properties at the bottom of a drainage path are where we see the most pumps, and where a failed one costs the most in one storm.
We cover Folsom, Cameron Park, Placerville, Granite Bay and dozens more communities across the western slope and greater Sacramento region.
Ready to schedule sump pump installation & repair?
Same-day service and a 60–90 minute emergency response across the western slope. Licensed, insured and upfront on price.
Good to know
Frequently asked questions
Related reading
Do El Dorado Hills Homes Need a Sump Pump?
Slab homes mostly skip sump pumps, but hillside lots, crawl spaces, and finished basements can need one. Here is how to tell which side of the line you are on.
EmergencySewer Backup After a Sierra Storm: A Homeowner Action Plan
Heavy Sierra storms push groundwater and runoff into aging sewer lines across El Dorado County. Here's the homeowner action plan for a backup, before and after it happens.